Welcome to our store Learn more

Up to 50% off on certain Certified Pre-Owned Broadcast Equipment

New collections added! Learn more

AFFORDABLE BLACKMAGIC EQUIPMENT. Broadcast Engineer standing by for queries.

SKU: S-BLA-BMAUMONA/PCBFRT

Blackmagic Design Spares - Blackmagic Audio Monitor - PCB Front

R 5,633.85 R 5,930.55
Tax included Shipping calculated at checkout.

The Blackmagic Design Spares - Blackmagic Audio Monitor - PCB Front is the interface and display board that sits directly behind the front panel of the 1RU rack unit. While the Main PCB handles the heavy lifting of signal de-embedding and processing, the Front PCB is responsible for the user-facing controls and the critical visual feedback.

This board is essentially the "face" of the device, containing the tactile buttons, the volume encoder, and the signature high-brightness LED level meters.

Core Responsibilities

  • LED Meter Drive: Manages the two 27-segment LED "ladders" that provide VU or PPM level monitoring.

  • Tactile Control: Houses the physical switches for input selection (SDI, AES/EBU, Analog) and solo/mute functions.

  • Volume Encoding: Features the rotary controller for the internal speakers and the $1/4$-inch headphone jack output logic.

  • Status Communication: Relays user input (like switching from SDI to Analog) back to the Main PCB to trigger the appropriate relays or processing paths.

When to Replace the Front PCB

  • Dead Meter Segments: If specific "bars" in the LED ladder stay dark while others around them light up, or if one entire side (Left or Right) is dark.

  • Unresponsive Buttons: If you press "SDI" or "Mute" and nothing happens, but the unit is otherwise passing audio.

  • Erratic Volume: If turning the volume knob causes the audio to jump wildly, "crackle," or fail to adjust (indicating a worn-out rotary encoder).

  • Headphone Jack Failure: If audio is fine through the speakers but the front-panel headphone jack is loose, distorted, or completely silent (the jack is typically soldered directly to this board).

Technical Installation Note

Repair Level: 2 (Moderate). This is a mechanical "sandwich" repair.

  1. Chassis Opening: You must remove the top cover of the unit and then unscrew the front faceplate.

  2. Ribbon Cable Handling: The Front PCB is connected to the Main PCB by one or two wide ribbon cables. Be careful: These cables are often tucked tightly. Ensure the locking tabs on the connectors are fully released before pulling.

  3. Knob Removal: You will likely need to pull off the external volume knob before the PCB can be separated from the metal faceplate. Some versions use a small set-screw (requires a $1.5\text{mm}$ or $2\text{mm}$ Hex key), while others are friction-fit.

  4. LED Alignment: When reassembling, ensure the LED towers are perfectly aligned with the plastic windows on the faceplate. If they are slightly tilted, the light will "bleed" into adjacent segments, making the meters hard to read.

Diagnostic: Front PCB vs. Main PCB

It can be tricky to tell which board has failed. Use this quick guide:

  • Scenario A: The unit produces sound through the speakers and the "SDI" light is on, but the level meters are totally dark.

    • Verdict: Likely a Front PCB failure.

  • Scenario B: The meters are dancing and showing audio levels, but there is no sound from the speakers or headphones.

    • Verdict: Likely a Main PCB or Internal Amp failure.

  • Scenario C: The buttons feel "mushy" or don't click, but the unit works if you control it via the USB software utility.

    • Verdict: Definitely the Front PCB.

Expert Advice: Before replacing the board for "erratic behavior," check the ribbon cable seating. Because these units are often mounted in mobile "fly-packs" or OB vans, vibration can sometimes cause the ribbon cable to wiggle loose, leading to flickering LEDs or unresponsive buttons.

Are your LED meters failing to show levels, or are the physical buttons simply not responding when pressed?

Blackmagic Design Spares - ATEM 1M/E Advanced Panel - Button
Blackmagic

Blackmagic Design Spares - Blackmagic Audio Monitor - PCB Front

R 5,633.85 R 5,930.55

The Blackmagic Design Spares - Blackmagic Audio Monitor - PCB Front is the interface and display board that sits directly behind the front panel of the 1RU rack unit. While the Main PCB handles the heavy lifting of signal de-embedding and processing, the Front PCB is responsible for the user-facing controls and the critical visual feedback.

This board is essentially the "face" of the device, containing the tactile buttons, the volume encoder, and the signature high-brightness LED level meters.

Core Responsibilities

  • LED Meter Drive: Manages the two 27-segment LED "ladders" that provide VU or PPM level monitoring.

  • Tactile Control: Houses the physical switches for input selection (SDI, AES/EBU, Analog) and solo/mute functions.

  • Volume Encoding: Features the rotary controller for the internal speakers and the $1/4$-inch headphone jack output logic.

  • Status Communication: Relays user input (like switching from SDI to Analog) back to the Main PCB to trigger the appropriate relays or processing paths.

When to Replace the Front PCB

  • Dead Meter Segments: If specific "bars" in the LED ladder stay dark while others around them light up, or if one entire side (Left or Right) is dark.

  • Unresponsive Buttons: If you press "SDI" or "Mute" and nothing happens, but the unit is otherwise passing audio.

  • Erratic Volume: If turning the volume knob causes the audio to jump wildly, "crackle," or fail to adjust (indicating a worn-out rotary encoder).

  • Headphone Jack Failure: If audio is fine through the speakers but the front-panel headphone jack is loose, distorted, or completely silent (the jack is typically soldered directly to this board).

Technical Installation Note

Repair Level: 2 (Moderate). This is a mechanical "sandwich" repair.

  1. Chassis Opening: You must remove the top cover of the unit and then unscrew the front faceplate.

  2. Ribbon Cable Handling: The Front PCB is connected to the Main PCB by one or two wide ribbon cables. Be careful: These cables are often tucked tightly. Ensure the locking tabs on the connectors are fully released before pulling.

  3. Knob Removal: You will likely need to pull off the external volume knob before the PCB can be separated from the metal faceplate. Some versions use a small set-screw (requires a $1.5\text{mm}$ or $2\text{mm}$ Hex key), while others are friction-fit.

  4. LED Alignment: When reassembling, ensure the LED towers are perfectly aligned with the plastic windows on the faceplate. If they are slightly tilted, the light will "bleed" into adjacent segments, making the meters hard to read.

Diagnostic: Front PCB vs. Main PCB

It can be tricky to tell which board has failed. Use this quick guide:

  • Scenario A: The unit produces sound through the speakers and the "SDI" light is on, but the level meters are totally dark.

    • Verdict: Likely a Front PCB failure.

  • Scenario B: The meters are dancing and showing audio levels, but there is no sound from the speakers or headphones.

    • Verdict: Likely a Main PCB or Internal Amp failure.

  • Scenario C: The buttons feel "mushy" or don't click, but the unit works if you control it via the USB software utility.

    • Verdict: Definitely the Front PCB.

Expert Advice: Before replacing the board for "erratic behavior," check the ribbon cable seating. Because these units are often mounted in mobile "fly-packs" or OB vans, vibration can sometimes cause the ribbon cable to wiggle loose, leading to flickering LEDs or unresponsive buttons.

Are your LED meters failing to show levels, or are the physical buttons simply not responding when pressed?

View product
Back to top